Outdoorcamera

Outdoor Wireless (ADC-V722W) – Installation Guide

Pre-installation checklist

  • ADC-V722W camera (included)
  • AC Power adapter (included)
  • Wireless (2.4 or 5 GHz) connection to broadband (Cable, DSL, or Fiber Optic) Internet
  • A computer, tablet, or smartphone with Wi-Fi is required if the router does not have the Wi-Fi Protected Setup (WPS) feature
  • Login and Password for the Alarm.com account to which you will add the camera

If the camera is already connected to the customer’s account but needs to be reconnected to a wireless network, see Reconnect a camera to a Wi-Fi network if the router, network equipment, or wireless settings change.

Add the camera to an Alarm.com account

To add a camera, connect the camera to the customer’s wireless network and then enroll the camera to the Alarm.com account. The camera can be connected to the wireless network using either Wi-Fi Protected Setup (WPS) mode or Access Point (AP) mode.

Important: When the camera is powered up, always allow at least two minutes before pressing any camera buttons. The first time a new video camera is powered up, it automatically goes into AP mode (flashing white) after two minutes.

AP mode

To ensure sufficient Wi-Fi signal, complete the following steps with the camera near its final location but prior to mounting.

  1. Connect the camera’s AC power adapter and plug it into a non-switched outlet. Allow at least two minutes before pressing any camera buttons.
  2. Press and hold down the WPS button and release when the LED begins to flash white (about 6 seconds).
  3. On an Internet-enabled device, connect to the wireless network ALARM (XX:XX:XX) where XX:XX:XX is the last six digits of the ADC-V722W’s MAC address, which is located on the back of the ADC-V722W.
  4. On the same device, open a web browser and enter http://722winstall or 192.168.1.1 in the web address field.
  5. Follow the on-screen instructions to add the ADC-V722W to the wireless network.
    1. Select a language for the instructions.
    2. Click Scan for Wi-Fi Networks.
    3. Click to select the customer’s Wi-Fi network.
    4. In the Security Key, enter the password of the customer’s Wi-Fi network. This is case-sensitive.
    5. Click Save.
    6. Click OK in the pop-up window that appears asking to refer to the website.
      • If this does not work, verify that the device is still connected to the ALARM(XX:XX:XX) network.
  6. When the LED is solid green, the wireless connection is complete.
  7. Add the video device to the account using either MobileTech, or entering the following web address: www.alarm.com/addcamera to access the Customer Website.
  8. Follow the on-screen instructions to add and set up the video device. For more information about adding a camera to an account, see Enroll the video device to the customer account.
  9. Once the camera is enrolled on the account, power down the camera and install it in its final location using the included hardware.
WPS mode

To ensure sufficient Wi-Fi signal, complete the following steps with the camera near its final location but prior to mounting.

  1. Connect the camera’s AC power adapter and plug it into a non-switched outlet. Allow at least two minutes before pressing any camera buttons.
  2. Press and hold down the WPS button and release when the LED begins to flash blue (about 3 seconds).
  3. Activate the WPS mode on the router. The camera begins to connect to the wireless network.
  4. When the LED is solid green, the wireless connection is complete.
    • If the LED is not solid green after a few minutes, retry WPS mode or try AP mode. For more information about WPS mode, see WPS Installation guide.
  5. Add the video device to the account using either MobileTech, or entering the following web address: www.alarm.com/addcamera to access the Customer Website.
  6. Follow the on-screen instructions to add and set up the video device. For more information about adding a camera to an account, see Enroll the video device to the customer account.
  7. Once the camera is enrolled on the account, power down the camera and install it in its final location using the included hardware.

LED reference guide

Connection status
Internet connection Local network and internet connection
Local network connection Local network connection only, no internet
No network connection No local network or internet connection
System booting Camera is booting
Wireless enrollment
WPS Mode To enter WPS mode, push the WPS button and release when flashing blue (about 3 seconds). For instructions about connecting the camera to the router using WPS mode, see WPS mode.
AP Mode To enter AP mode, push the WPS button and release when flashing white (about 6 seconds). For instructions about connecting the camera to the router using AP mode, see AP mode.
Factory reset
Factory Reset Caution: This restores factory-default settings to the camera.

If already installed, the camera may need to be removed from the Alarm.com account and re-added after a factory reset.

To perform a factory reset, push the WPS button and release when flashing Green and Red (about 15 seconds).

Troubleshooting

  • If you have issues connecting the camera to the account, power cycle the camera and try again.
  • If issues persist, reset the camera to factory defaults by using the WPS button located on the back of the camera. Press and hold the WPS button until the LED is flashing Green and Red (about 15 seconds), then release the button. The camera reboots with factory defaults. If the camera was previously installed to an Alarm. com account, it needs to be deleted before it can be installed again.

Call Today Installed Tomorrow

Sidebar Form

FREE Home Security Review

We respect your email privacy

Recent Blog Articles
Recent Blog Articles

Follow Us

Receive up to $850 of free equipment!